We have stumbled upon this great article relating to How to Install a Bathtub below on the internet and decided it made sense to discuss it with you over here.
Mounting a bathtub isn't exactly rocket science, but it does call for solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably difficult project. If the old bathtub is readily easily accessible, the project can relocate speedily; if you have to open up a wall to eliminate the old bathtub as well as position the new bath tub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and also set in the brand-new one. Ensure you have actually qualified yourself for the job as well as are comfortable attempting it. Instead of hiring a professional to take over a halfway-completed job, it is better to consider utilizing one prior to you begin. Possibilities are you may require an expert plumber to make tube links.
This write-up will help you set up a new bathtub in your shower room if you have actually already purchased a brand-new tub and also do not need to transform the arrangement of your previous water system pipes.
Your devices and also product list ought to comprise the following:
Preparing for the Installation
Firstly, the supporting structure supplied with the bathroom must be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the versatile faucet connectors to the bottom of both taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you should do is disconnect the water supply. After doing so, switch on the taps to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome as a result of the restricted accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from turning throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the tub in the required setting. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The following goal is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the tub until the level reviews degree.
To set up taps, fit all-time low of the furthest flexible tap port to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Activate the supply of water as well as inspect all joints and new pipework for leakages and also tighten them if required. Fill up the bath tub and likewise inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, deal with the bath paneling as described in the maker's user's manual. Tiling and securing around the bath tub needs to wait till the tub has been made use of at least once as this will certainly settle it right into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in place in between the tap and the sink. Protect the tap in place with the producer provided backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet ports. The previous kind should be linked to the tap ends first, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall surface between the bath as well as the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to allow for the movement experienced when the tub is in usage. The sealer can split relatively very early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about Installing A Bathtub? Create a comment below. We would be delighted to know your opinions about this posting. In hopes that you visit us again later on. Sharing is nice. Helping people is fun. Thank you so much for going through it.
Reliable every time!